-
125LY-35-4 Lube Oil Pump Shaft Seal Leaks — How to Find the Cause and When to Replace
A dripping shaft seal on a turbine lube oil pump is one of those problems that looks minor until it isn’t. A few drops per hour turns into a puddle, the puddle becomes a housekeeping issue, and somewhere in the background the question nobody wants to answer is whether the seal is about to f...Read more -
Hydrogen Dryer Trap Valve 1F05407: What Really Happens When It Gets Stuck
Nobody thinks much about the condensate trap valve on a hydrogen dryer until the dewpoint starts climbing or a hydrogen detector goes off. It’s one of those parts that just quietly does its job — or quietly stops doing it — and you don’t always know which until something downstream go...Read more -
G771K202A Servo Valve: Diagnosing Pilot Stage Faults, Spool Wear, and What a Proper Repair Report Should Show
When a gas turbine starts showing load fluctuations or the steam valves are responding slower than they should, the G771K202A servo valve is usually one of the first things that comes up. It sits right between the DEH control system’s electrical output and the hydraulic actuator that actual...Read more -
DG4V-3-2AL-M-U-D6-60 Solenoid Directional Valve: How to Detect Spool Sticking Before It Takes Down a Turbine Actuator
A solenoid directional valve that’s starting to stick doesn’t usually announce itself. The symptoms come gradually — a slightly sluggish actuator response, a pressure transient that’s a bit more pronounced than it used to be, an operation that takes a fraction of a second longer...Read more -
Can’t Build Pressure in Your Mill Hydraulic Station? The MRV-03-B-3-B Stack Seal Problem Explained
Coal mill hydraulic loading systems don’t give much warning before a pressure problem shows up. The mill is running, the loading cylinder is supposed to be holding the grinding pressure, and then the system either can’t build pressure at all or it builds and bleeds off faster than it ...Read more -
Why Does the DBDS20K10/315 Relief Valve Lose Set Pressure — and How Much Drift Is Too Much?
Direct-acting relief valves don’t get much attention until something goes wrong. They sit in the hydraulic circuit, do their job quietly, and most maintenance teams only think about them when a pressure alarm shows up or the system starts behaving oddly. The DBDS20K10/315 is that kind of va...Read more -
The DQ8302GA15H3.5C Jacking Oil Filter — Small Part, Big Consequences When It Goes Wrong
The jacking oil system on a steam turbine doesn’t run all the time — just during startup and shutdown, when the rotor is turning slowly or barely moving at all. But those are exactly the moments when bearing protection matters most. At low shaft speed there’s no hydrodynamic oil film ...Read more -
C14633-001V Gas Turbine Actuator Filter: What It Does, Why It Fails, and How to Stay Ahead of It
The inlet guide vanes on a gas turbine are constantly moving. Every time load changes, every startup, every control system adjustment — the IGV actuator responds. That’s a lot of hydraulic activity, and all that oil flowing back and forth through the actuator circuit needs to stay clean. If...Read more -
SZ3-1-20/5 Cooling Water Filter for Generator Stator Systems: What You Need to Know
Generator stator cooling is one of those systems that doesn’t get much attention until something goes wrong — and by then, the consequences are usually significant. The stator windings in a large power plant generator carry enormous current, and the water flowing through them is what keeps ...Read more -
DR1A401EA03V Fire-Resistant Oil Return Filter: Role, Performance, and What Happens When It Blocks
Most people working on a steam turbine EH oil system pay close attention to the pump outlet filter — that’s the one protecting the servo valves and actuators directly, so it makes sense. The oil return filter gets less attention, but letting it go too long between replacements causes proble...Read more -
0160D005BN3HC Pleated Hydraulic Filter: What It Does and How to Replace It Without Causing More Problems
If you work around hydraulic systems in a power plant, you already know that keeping the fluid clean is half the battle. Servo valves, actuators, control cylinders — these things have incredibly tight internal clearances, and once contamination gets into the oil circuit, it doesn’t just dis...Read more -
DC-4 Air Filter for Steam Turbine EH Oil Tanks: Performance, Environment, and What to Watch For
The EH oil system on a steam turbine runs on fire-resistant hydraulic fluid — expensive, chemically sensitive, and unforgiving when it gets contaminated. Most of the protection work happens inside the system, through pressure filters and fluid conditioning equipment. But there’s a small com...Read more
/
Company News
- English
- French
- German
- Portuguese
- Spanish
- Russian
- Japanese
- Korean
- Arabic
- Irish
- Greek
- Turkish
- Italian
- Danish
- Romanian
- Indonesian
- Czech
- Afrikaans
- Swedish
- Polish
- Basque
- Catalan
- Esperanto
- Hindi
- Lao
- Albanian
- Amharic
- Armenian
- Azerbaijani
- Belarusian
- Bengali
- Bosnian
- Bulgarian
- Cebuano
- Chichewa
- Corsican
- Croatian
- Dutch
- Estonian
- Filipino
- Finnish
- Frisian
- Galician
- Georgian
- Gujarati
- Haitian
- Hausa
- Hawaiian
- Hebrew
- Hmong
- Hungarian
- Icelandic
- Igbo
- Javanese
- Kannada
- Kazakh
- Khmer
- Kurdish
- Kyrgyz
- Latin
- Latvian
- Lithuanian
- Luxembou..
- Macedonian
- Malagasy
- Malay
- Malayalam
- Maltese
- Maori
- Marathi
- Mongolian
- Burmese
- Nepali
- Norwegian
- Pashto
- Persian
- Punjabi
- Serbian
- Sesotho
- Sinhala
- Slovak
- Slovenian
- Somali
- Samoan
- Scots Gaelic
- Shona
- Sindhi
- Sundanese
- Swahili
- Tajik
- Tamil
- Telugu
- Thai
- Ukrainian
- Urdu
- Uzbek
- Vietnamese
- Welsh
- Xhosa
- Yiddish
- Yoruba
- Zulu
- Kinyarwanda
- Tatar
- Oriya
- Turkmen
- Uyghur