Company News |

ZJ-20-T6 Electric Heating Rod: When the Bolt Won’t Stretch Enough
by admin on 26-09-15
Thermal tightening depends on a number. The bolt needs to elongate by a specific amount, within a specific time, or the joint doesn’t come together with the preload it’s supposed to have. When that elongation falls short and the heating rod‘s insulation resistance still checks o...
Read more
SZMB-9 Magnetoelectric Speed Sensor: Same Frequency, Fading Signal
by admin on 26-09-15
Frequency tells you speed. Amplitude tells you something else — how much signal the sensor is actually managing to generate. On a magnetoelectric speed sensor, watching amplitude slowly drop while frequency stays exactly where it should be is a specific kind of warning, different from a sensor go...
Read more
TD-2-26 Expansion Sensor: When the Needle and the Screen Don’t Agree
by admin on 26-09-14
Turbine casing expansion has to be watched closely during startup and load changes. Too much differential expansion, and clearances inside the turbine start closing up in places they shouldn’t. The TD-2-26 is an LVDT displacement sensor built for exactly this measurement, feeding both a loc...
Read more
S3-VD-3-15A40 Voltage Transmitter: When Two Displays Disagree
by admin on 26-09-14
DCS says one voltage. The panel meter at the switchgear says another. Not wildly different — just off, consistently, by a small but noticeable margin. Someone’s already ruled out the PT secondary circuit. So the mismatch lives somewhere between the transmitter and the DCS input card, and th...
Read more
Slide Gate Valve Spare Parts Kit 200×200 PN1.0: Scratch or Just a Trapped Particle?
by admin on 26-09-11
Coal conveyor lines leak a little after the gate shuts. Fine material gets past the seal, downstream side, right after closure. Most of the time it’s nothing — a bit of ash or pulverized coal sitting between the plate and the seat, gone by the next cycle. Sometimes it’s a groove worn ...
Read more
A2201 Seal Kit: Reading a Sluggish Dome Valve Before You Open It
by admin on 26-09-11
A dome valve that used to snap open and closed now takes its time. Maybe it pauses partway through the stroke. Someone checks the air pressure gauge. Normal. So what now? The A2201 seal kit rebuilds the actuator cylinder on a DN100 pneumatic conveying dome valve. Worn internal seals are one usual...
Read more
D633-460B Servo Valve: Jitter, Drift, and the Risk of Fixing It Wrong
by admin on 26-09-10
A servo valve like the D633-460B sits at the center of DEH position control. It moves the main steam valve and the governing valve to exact positions, based on an electrical command. Feedback tells the system where the valve actually sits. When that feedback starts jittering, or the zero point dr...
Read more
P17458C-01 Embedded Sealing Ring: Chasing Dust Leaks That Come and Go
by admin on 26-09-10
A dome valve seals by inflating a ring, not by clamping metal on metal. The P17458C-01 is that ring — silicone rubber, built into the dome valve, expanding under air pressure to press against the dome and shut off dust flow. Simple concept. But when dust starts leaking after the valve closes, and...
Read more
SFQ41F-16C Double Ball Valve: The Standby Side Problem
by admin on 26-09-09
Two outlets, one valve body. That is the basic idea behind the SFQ41F-16C ball valve. One line stays in service. The other sits ready, waiting for a switch, a maintenance need, or a flow split. Simple on paper. In an oil station running for years without stopping, the standby side raises a questi...
Read more
DBDS10G10/5 Direct-Acting Relief Valve: Reading a Low-Pressure Fault
by admin on 26-09-09
A relief valve has one job. Open when pressure is too high. Stay shut the rest of the time. The DBDS10G10/5 is a direct-acting relief valve with a poppet-style spool. It can act as a safety valve, protecting the system from over-pressure. It can also act as a back-pressure valve, holding pressure...
Read more
DG4V-3-2A-VM-U-SA7-60 Solenoid Directional Control Valve: What Happens When It Doesn’t Fully Reset
by admin on 26-09-08
There is a kind of failure in EH oil and jacking oil systems that does not show up as an alarm right away. The valve does not fail closed. It does not fail open. It just does not quite get all the way back to where it should be. A solenoid directional control valve like the DG4V-3-2A-VM-U-SA7-60 ...
Read more
YOX II500 Hydraulic Coupling with Brake: Does the Brake Really Wear Out the Output Bearing?
by admin on 26-09-08
Coal handling equipment doesn’t get treated gently. Conveyor belts start up under load, coal mills need protecting from jams and blockages, and somewhere between the motor and the driven equipment you need something that can soak up a soft start and step in when things go wrong. A hydraulic...
Read more