LY48-25 Oil Filter: Precision Bearing Filtration Solutions for Small Steam Turbines

In the lube oil stations of feed pump turbines, the LY48-25 oil filter acts as the critical line of defense for precision bearings. These bearings rely on a clean lubricant film to operate; even microscopic impurities or oil contamination can cause wear and seizing. The compatibility between filtration precision and dirt-holding capacity directly determines the bearing’s lifespan. To avoid failure risks, you must choose and use this filter correctly, ensuring its performance aligns with bearing protection needs. As the heart of the system, the stability of the oil filter element is the top priority.

I. Filtration Precision: Meeting Bearing Needs

The precision bearings in small steam turbines have tiny clearances. Micron-sized particles can shred the oil film. Therefore, the filtration precision of the LY48-25 oil filter must be accurately matched to these specs. If the precision is too high, the oil filter element will clog constantly, choking the oil cycle. Too low, and harmful debris gets through.

You should determine the precision grade based on bearing material and operating conditions. For high-speed precision bearings, prioritize a dedicated LY48-25 oil filter element to ensure fine particles are caught without slowing down the oil flow.

If you aren’t sure about the right precision for your unit, contact us for customized selection advice.

II. Dirt-Holding Capacity: Handling Impurities Under Load

Dirt-holding capacity determines the service life and stability of the oil filter element. During feed pump turbine operation, lube oil picks up metal shavings and dust. If the capacity is too low, the element saturates too fast.

The capacity of the LY48-25 oil filter must match the unit’s runtime and the rate of debris generation. For turbines running under long-term high loads, you should use high-capacity elements to reduce replacement frequency. The LY48-25 oil filter element we supply is designed specifically for these harsh power plant conditions. A saturated element causes a spike in pressure differential, which can lead to oil starvation at the bearings.

III. Practical Compatibility: Implementing Protection

When installing an LY48-25 oil filter, always verify that the element specs match the filter housing. Non-OEM elements often suffer from precision errors or poor dirt-holding capacity, leading to total filtration failure.

• Check the Seals: Regularly inspect the sealing performance. A bad seal allows unfiltered oil to leak into the bearing oil path.
• Tight Fit: Ensure the oil filter element sits tight against the housing surface with no grit or old oil trapped in the seal area.
• Adjust Cycles: Use your oil cleanliness test results to adjust your replacement schedule. If contamination is high, shorten the interval or add a pre-filter.

Need a pre-filtration system design? Contact us for technical support.

IV. Maintenance: Balancing Filtration and Protection

Daily walkdowns should focus on the state of the oil filter element:

1. Monitor the Gauge: Use the differential pressure gauge to track the element’s health. Replace it immediately if it exceeds the set value.
2. Clean the Housing: When swapping the oil filter element, clean the inside of the filter shell. Remove residual sludge to prevent cross-contamination.
3. Use Genuine Parts: Stick with original LY48-25 oil filter parts to ensure the precision and capacity match your original equipment perfectly.

V. Conclusion: Guarding Bearings Through Precise Matching

The precision and dirt-holding capacity of the LY48-25 oil filter are the primary safeguards for small turbine bearings. By choosing the right oil filter element and keeping up with maintenance, you can extend bearing life and lower your O&M costs.

Need original LY48-25 oil filter elements, selection guidance, or on-site support? Contact us. We provide high-quality filter elements and professional services to help you achieve reliable protection and stable unit operation.
E-mail: sales@yoyik.com
Tel: +86-838-2226655
Whatsapp: +86-13618105229

Yoyik offers various types of power plants spare parts for steam turbines, generators, boilers as below:
high pressure hydraulic filter elements DHLX10JSN
hydraulic filter manufacturers TFX-25*100 EH oil station EH oil main pump suction filter
filter steel mesh WU-100×100-J Pre Filter
hydraulic filter micron size 0660-D-020-BN3HC
hydraulic return line LH0330D020BN/HC
pleated filter cartridge manufacturer HY1-100-003-F
inlet suction strainer 01-535-042
filter element oil QU-H40*10BDP
hydraulic system filter FRD.7Z8L4X.206A
hydraulic return line SGF-H110x10F-C
filter industrial C9209011 EH oil filter
filtration industry ZNGL02011201
strainer in hydraulic system SFX-660*20 Jacking oil filter
filter element companies DZ903EA01V/-W Hydraulic Oil Regenerative Filter Element
full flow oil filter SLAF-10HT
filter press hydraulic power pack QTL6021
pleated filter element 0508.1020T0101AW
oil filtration systems G-RK108251
industrial liquid filtration 2-5685-0012-00
stainless steel micron filter 01-094-002 Resin filter element
oil filter element material LY-38/25W lube system fan filter
pp water filter SG125/0.7 generator stator cooling water filter
hydraulic oil filter unit HC9801FHT4Z
filter element 1002511875
turbine oil purification system 200652304
KLS-50U/80 generator stator cooling water station ion exchange outlet filter